Smart Lock (9910) – Installation Guide
Adjust the backset (extend if needed).Install the Latch and Strike.Prepare exterior keypad (use adapter ring if needed).Install the exterior assembly and mounting plate (interior). Do not over-tighten.Install the interior assembly.
How do I connect my Vivint lock to my door?
To add a thermostat, door lock, or module to your system, complete the following steps:
Go to your touchscreen panel and touch the home button.Tap Services.Tap the wrench icon.Enter your 4-digit PIN.Tap Add Devices.At this point, go to the device you want to add (door lock, thermostats, light module, etc.).
How much does a Vivint door lock cost?
Typically, we see prices range between $125 on the low end, and upwards of $300+ for high-end devices. Vivint’s Kwikset 880 SmartCode comes in at $179.99. We think it’s a fair price, but keep in mind that you’ll need other equipment like Vivint’s sensors, the Smart Hub, and probably a security camera or two.
What door lock does Vivint use?
Vivint mainly uses Kwikset Z-Wave based smart locks and here are the models that work best with the Vivint security system: Kwikset SmartCode 888 Smart Lock.
What is the installer code for vivint?
Enter the default installer PIN code (2203) 3. Select the device to control 4.
Can I add my own smart lock to Vivint?
If you’ve just purchased the Vivint security devices, note that Vivint isn’t a DIY system; you need to contact the company to send a pro to set up the security system. Once the Vivint system is in place, it’s easy to connect your compatible Kwikset smart lock.
Which Kwikset locks work with Vivint?
Kwikset locks integrate with your Vivint system to ensure your entryway—and home—is protected.
Kwikset and Vivint bring you peace-of-mind protection.
Satin Nickel. 888 SmartCode Electronic Deadbolt with Z-Wave Technology.Venetian Bronze. Polished Brass.
Will any Z-Wave work with Vivint?
Before onboarding any connected devices to the Vivint system, it’s important to know the platform is based on a Z-Wave wireless protocol — meaning most Z-Wave devices will work with on the Vivint platform, especially smart locks and lights.
Is Vivint overpriced?
Vivint is more expensive than most of the other companies in our rating of the Best Home Security System of 2022. You can finance the cost of equipment for 42 or 60 months with no down payment and no interest, or you can pay upfront.
Can I use Vivint door lock without service?
Can I use Vivint without a subscription? You can use Vivint equipment without a subscription, but you wouldn’t have the benefit of professional monitoring, couldn’t access the mobile application, and won’t be able to use the 24/7 technical support service.
Can you negotiate with Vivint?
Yes, you can negotiate with your Vivint sales representative when you set up a contract with Vivint. You might negotiate about your options to purchase all your equipment up front in one payment or determine monthly finance options.
What is Z-Wave door lock?
Smart locks provide you with peace of mind security allowing you to know who is coming and going from your home. Once the smart lock is connected to the smart hub, you now can remotely access your lock to lock or unlock your doors from anywhere in the world. Safer, smarter homes are locked with Z-Wave.
What is Vivint master code?
From the home screen of the 2GIG GC2, go to Security > Menu > Toolbox > enter the current master code (the default code is 1111) > User Management. You will now be in the user management menu.
How do you reset Vivint without code?
Hardware: Press and hold the Reset button on the back of the router for 10-15 seconds, then release. Software: In the Configuration Interface, go to the Advanced tab and under the Administration tab click Factory Defaults. Then click the Restore Factory Defaults button.
How do I add Z-Wave to Vivint?
At the Vivint panel, press the Home button, then select the three dots in the bottom right-hand corner of the panel. Select Software Version and enter the 4-digit code that appeared in Site Manager after unlocking the Installer Toolbox. Select Smart Home Devices > Z-wave > Add Node.
