The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
Can you apply sealer with a pump sprayer?
Yes, you can use a standard pump garden sprayer to apply your sealant. Or at least, you can if you’re applying a water-based sealer. Since solvent-based sealers have more active chemicals and corrosive agents, they are not recommended for garden sprayers.
How many coats of Thompson Water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water. Let the deck dry for at least 24 hours and you’re ready to replace the furniture.
How often does Thompson’s water Seal need to be applied?
Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure. All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck.
Is it better to roll or spray concrete sealer?
Slow-evaporating solvents are better for rolling. If the product is sprayed, I like to back-roll on the primer (first) application. This works the material into the surface and improves the adhesion.”“Most decorative contractors, when doing a large area, prefer the spray/back-roll method,” Platt says.
Is it better to roll or spray paver sealer?
As long as you apply the paver sealer on a windless day, the coverage can be generous and effortless. If you really cant get a pump up garden sprayer, opt for a sponge-type roller to apply the sealer. A nap roller is more likely to grab and trap your joint sand. I recommend spraying when applying brick paver sealer.
How do you spray seal wood?
Simply open up your stain sprayer and pour in your wood stain or mix. Then turn and seal the lid counter-clockwise to create an air seal. This allows you to build up the vacuum within the sprayer so you can spray it as needed. The sprayer will have a handle coming from the top near the hose.
Can you use too much Thompson water Seal?
The sealant may also take longer to dry if you apply it in excess or if the surface already has a previous one coat of sealant on it. You may also notice tackiness on the sealed surface if you do not give sufficient drying time or if the weather is too cold to facilitate the drying process.
How long before you can walk on Thompson water Seal?
Now that you’ve applied Thompson’s Water Seal following the instructions above, to your entire surface, you can walk away and let it dry for 24 hours. That’s all the time you need to let Thompson’s Water Seal work to protect your outdoor surfaces from water damage.
How much will a gallon of Thompson water Seal cover?
That determines how many gallons of stain are required (each gallon covers up to 400 square feet). You can buy it and be on your way. Thanks to its pigment-suspension technology, there’s no need to wait for the Waterpoofing Stain to have its turn in the paint shaker.
Can you put Thompson water Seal on treated wood?
Other products, like Thompson’s® WaterSeal® Waterproofing Stain, can be applied immediately to new pressure treated lumber. New cedar and redwood can always be treated immediately.
Can you put Thompson’s water Seal on wet wood?
Surfaces must be thoroughly cleaned prior to application with a deck cleaner (like those in the Thompson’s® WaterSeal® cleaner line) applied according to label directions and cautions. If surface is damp or wet from cleaning or weather, allow the surface to dry thoroughly (a minimum of 48 hours) before application.
How long does Thompson’s water Seal last in the can?
How long will Water Seal last? If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
