Thermocouples are designed to detect a pilot light’s loss of heat and close the gas valve to prevent a gas leak. Replacing a thermocouple is a relatively easy fix that can take less than two hours.
How do you clean a thermocouple on a GE water heater?
Clean the thermocouple – using the emery cloth sandpaper, sand the ends of the thermocouple and then give it a finishing touch with the lint-free cloth. Hopefully, you can get to the ends of the thermocouple without having to detach it from the assembly, but you may have to do that.
Are water heater thermocouples universal?
Universal thermocouples come in lengths from 15 to 36 inches. An 18 or 24 inch will suffice for all residential water heaters using universal kits. Almost all older waters heaters and many of the newer style units with a sealed burner compartment and a viewing window will use this thermocouple.
How much does it cost to replace thermocouple?
It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on. It will shut the gas off if it’s not.
How long does a thermocouple last on a water heater?
In effect, new thermocouples were installed into contaminated tubes, causing the degradation of the sensors and generating greater than a 100°F shift in accuracy. In this scenario, thermocouple life, which should have been close to one year, was shortened to within a week.
How do I know if my thermocouple is bad on my water heater?
If the pilot lights but the flame goes out as soon as you release the button after holding it for 60 seconds, then the thermocouple is bad. It’s possible to replace the thermocouple without removing the burner assembly, and many repair people do this.
How much is a water heater thermocouple?
Thermocouple – $20 to $150
The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.
Why does the pilot on my water heater keep going out?
Thermocouple Issues
If it senses that your water heater pilot light keeps going out, the thermocouple will shift off the gas supply to the heater. Over time, thermocouples can malfunction, accumulate dust buildup, or the device can get bent away from the pilot light’s flame.
Does cleaning a thermocouple work?
Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up. Cleaning a thermocouple is not a fix for an issue, such as inaccurate readings.
Can you bypass a water heater thermocouple?
Realistically, you have just disabled the thermocouple, but you can also reach in and unclip it from its holding bracket where it meets the pilot light. In most cases it will be held on with a gravity clip, but some are held on with a screw that must be removed with a small screwdriver.
Can a water heater thermocouple be cleaned?
You can use Emery cloth sandpaper to gently clean any debris or build-up from the end of the thermocouple. If present, you should also clean off any corrosion where the power wire connects to the thermocouple terminal. Be aware, you may need to detach the thermocouple from the burner assembly to clean it thoroughly.
Are all thermocouples compatible?
Commercial thermocouples are interchangeable, economical, and supplied with standard connectors. Unlike most other temperature measurement devices, external form of excitation is not required for thermocouples because they are self-powered.
Can I use any thermocouple?
Watch out: thermopiles and thermocouples are not interchangeable. When replacing a temperature sensing device like a thermocouple or thermopile, you should be sure to purchase the proper part.
How do I choose a thermocouple?
How to choose a Thermocouple
Determine the application where you will use the thermocouple sensor. Determine the temperature ranges the probe will be exposed to. Determine how important a fast response time is. Consider any chemical, abrasion or vibration resistance. Consider any installation requirements.
What do you do when your pilot light keeps going out?
Once The Flame Is Lit, Turn Gas Control Valve to “On”
Once the pilot light is ignited, you can release the reset button after 30 seconds and turn the gas knob to the “On” position. At this time you should hear the main burner come on. Now your pilot light should hold a flame and hot water should be restored!
