A Whirlpool washer E1 or F9 error code (FP with some models) means that the washer is taking too long to drain (typically, over 8 minutes).
How to Fix Whirlpool Washer E1/F9 Error Codes
Try a Reset. Check your Detergent. Check the Drain Hose. Clean the Filter. Check the Drain Pump. Check the Wiring.
What does F9 E1 mean on my Whirlpool washer?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub.
How do I clear the error on my Whirlpool washing machine?
Manual Review
Unplug the Whirlpool washing machine from the mains.Wait for 15-20 minutes while the control unit reboots.Reset the error by pressing the START button (On/Off).Check hatch locking.
How do you fix F3 E1 error on a Whirlpool washer?
F3 E1 Error Code
Power unit down by turning off the circuit breaker or unplugging for one (1) minute.Power unit up by reconnecting power.Restart a new cycle.Monitor the washer for one (1) minute to ensure the error code does not display again.
How do you manually unlock a Whirlpool washer?
Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
What does E01 mean on a washing machine?
E01 – there’s an issue with the lock, its wiring or connection to the control board. Check the door is closed properly and the wiring is intact. E02 – the machine has failed to fill with water during its allocated time.
What is E1 f3 Whirlpool washer?
The Whirlpool washer F3E1 error code is a water level system error. The main control is detecting an out of range pressure signal. Check the water level pressure hose from the water level pressure sensor to the air trap.
What is the meaning of dE error in Whirlpool washing machine?
A dE error code indicates that the washer door was unable to lock. This can normally be resolved by performing a simple reset on the washing machine.
How do you clear the error code on a Whirlpool Cabrio washer?
Write Down The Error Code!
Then press PAUSE/CANCEL once to clear the error code and try to start a new cycle. If code appears again put the washer through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea. (Watch The Cabrio Diagnostics Video) This will reveal any stored Cabrio error codes.
How do I fix error code E1 F3?
Step 1 – Reset Your Washer. The best place to start is to do a simple reset of your washer. Step 2 – Check the Switch Hose. Step 3 – Check the Water Level Sensor. Step 4 – Check the Air Trap Pipe. Step 5 – Check the Wiring. Step 6 – Replace the Control Board. 9 Reasons Your Refrigerator Isn’t Cooling.
What does E1 F8 mean on a Whirlpool washer?
If F8 E1 or LF (too long to fill) appears in display, it means the washer is taking too long to fill. It’s possible the drain hose extends more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation.
Why is my washer locked and won’t open?
The most common cause is water left in the machine. Try running a spin/drain cycle. If this fails, the machine can be drained by placing the washing machine drain hose lower than the drum (into a bucket or tray). The door interlock has simply jammed.
How do I unlock my Whirlpool washer without power?
If the door doesn’t open as it should after the cycle has ended, the next step is to hold the “control lock” button down for 3 seconds. You should be able to hear an unlatching sound followed by being able to open the door.
How do you unlock the control lock on a Whirlpool washing machine?
If you do not see the 3-2-1 countdown and are unable to de-activate Control Lock, try pressing the POWER button first, then touch and hold 3 seconds to de-activate control lock. If this does not work, try unplugging the machine or turning off the breaker for 1 minute, then power the machine back on and try again.
